System Deployment

The DAOS deployment workflow requires to start the DAOS server instances early on to enable administrators to perform remote operations in parallel across multiple storage nodes via the dmg management utility. Security is guaranteed via the use of certificates. The first type of commands run after installation include network and storage hardware provisioning and would typically be run from a login node.

After daos_server instances have been started on each storage node for the first time, daos_server scm prepare will set PMem storage into the necessary state for use with DAOS when run on each host. Then dmg storage format formats persistent storage devices (specified in the server configuration file) on the storage nodes and writes necessary metadata before starting DAOS I/O engine processes that will operate across the fabric.

To sum up, the typical workflow of a DAOS system deployment consists of the following steps:

• Configure and start the DAOS server.

• Provision Hardware on all the storage nodes via the dmg utility.

• Format the DAOS system

• Set up and start the agent on the client nodes

• Validate that the DAOS system is operational

Note

Starting the DAOS server instances can be performed automatically on boot if start-up scripts are registered with systemd.

The following subsections will cover each step in more detail.

DAOS Server Setup

First of all, the DAOS server should be started to allow remote administration command to be executed via the dmg tool. This section describes the minimal DAOS server configuration and how to start it on all the storage nodes.

Example RPM Deployment Workflow

A recommended workflow to get up and running is as follows:

• Install DAOS Server RPMs - daos_server systemd services will start in listening mode which means DAOS I/O engine processes will not be started as the server config file (default location at /etc/daos/daos_server.yml) has not yet been populated.

• Run dmg config generate -l <hostset> -a <access_points> across the entire hostset (all the storage servers that are now running the daos_server service after RPM install). The command will only generate a config if hardware setups on all the hosts are similar and have been given sensible NUMA mappings. Adjust the hostset until you have a set with homogeneous hardware configurations.

• Once a recommended config file can be generated, copy it to the server config file default location (/etc/daos/daos_server.yml) on each DAOS Server host and restart all daos_server services. An example command to restart the services is clush -w machines-[118-121,130-133] "sudo systemctl restart daos_server". The services should prompt for format on restart and after format is triggered from dmg, the DAOS I/O engine processes should start.

Server Configuration File

The daos_server configuration file is parsed when starting the daos_server process. The configuration file location can be specified on the command line (daos_server -h for usage) otherwise it will be read from the default location (/etc/daos/daos_server.yml).

Parameter descriptions are specified in daos_server.yml and example configuration files in the examples directory.

Any option supplied to daos_server as a command line option or flag will take precedence over equivalent configuration file parameter.

For convenience, active parsed configuration values are written to a temporary file for reference, and the location will be written to the log.

Configuration Options

The example configuration file lists the default empty configuration, listing all the options (living documentation of the config file). Live examples are available at https://github.com/daos-stack/daos/tree/release/2.4/utils/config/examples

The location of this configuration file is determined by first checking for the path specified through the -o option of the daos_server command line, if unspecified then /etc/daos/daos_server.yml is used.

Refer to the example configuration file daos_server.yml for latest information and examples.

Auto Generate Configuration File

DAOS can attempt to produce a server configuration file that makes optimal use of hardware on a given set of hosts either through the dmg or daos_server tools.

Generating Configuration File Using daos_server Tool

To generate a configuration file for a single storage server, run the daos_server config generate command locally. In this case, the daos_server service should not be running on the local host.

daos_server scm prepare should be run prior to daos_server config generate if the intent is to use PMem for SCM. This will allow the relevant storage to be available for detection when attempting to generate the configuration files.

$ daos_server config generate --help
Usage:
  daos_server [OPTIONS] config generate [generate-OPTIONS]

Application Options:
      --allow-proxy                         Allow proxy configuration via environment
  -o, --config=                             Server config file path
  -b, --debug                               Enable debug output
  -j, --json                                enable JSON output
  -J, --json-logging                        Enable JSON-formatted log output
      --syslog                              Enable logging to syslog

Help Options:
  -h, --help                                Show this help message

[generate command options]
      -l, --helper-log-file=                Log file location for debug from daos_server_helper binary
      -a, --access-points=                  Comma separated list of access point addresses
                                            <ipv4addr/hostname> (default: localhost)
      -e, --num-engines=                    Set the number of DAOS Engine sections to be populated in the
                                            config file output. If unset then the value will be set to the
                                            number of NUMA nodes on storage hosts in the DAOS system.
      -s, --scm-only                        Create a SCM-only config without NVMe SSDs.
      -c, --net-class=[ethernet|infiniband] Set the network device class to be used (default: infiniband)
      -p, --net-provider=                   Set the network fabric provider to be used
      -t, --use-tmpfs-scm                   Use tmpfs for scm rather than PMem
      -m, --control-metadata-path=          External storage path to store control metadata. Set this to
                                            a persistent location and specify --use-tmpfs-scm to create an
                                            MD-on-SSD config
      -f, --fabric-ports=                   Allow custom fabric interface ports to be specified for each engine
                                            config section. Comma separated port numbers, one per engine
          --skip-prep                       Skip preparation of devices during scan.

Note the --helper-log-file which can be used to provide a log file path to output debug level logging from the privileged server helper binary. This can be used for troubleshooting in addition to the main application debug flag.

Generating Configuration File Using dmg Tool

To generate a configuration file for a group of storage servers with homogeneous hardware installed, dmg config generate command can be called which will operate over remote addresses specified in the --host-list application option (the hostlist can also be specified in the dmg client config).

$ dmg config generate --help
Usage:
  dmg [OPTIONS] config generate [generate-OPTIONS]

Application Options:
      --allow-proxy                         Allow proxy configuration via environment
  -i, --insecure                            Have dmg attempt to connect without certificates
  -d, --debug                               Enable debug output
      --log-file=                           Log command output to the specified file
  -j, --json                                Enable JSON output
  -J, --json-logging                        Enable JSON-formatted log output
  -o, --config-path=                        Client config file path

Help Options:
  -h, --help                                Show this help message

[generate command options]
      -l, --host-list=                      A comma separated list of addresses <ipv4addr/hostname> to connect to
      -a, --access-points=                  Comma separated list of access point addresses <ipv4addr/hostname>
                                            to host management service (default: localhost)
      -e, --num-engines=                    Set the number of DAOS Engine sections to be populated in the
                                            config file output. If unset then the value will be set to the
                                            number of NUMA nodes on storage hosts in the DAOS system.
      -s, --scm-only                        Create a SCM-only config without NVMe SSDs.
      -c, --net-class=[ethernet|infiniband] Set the network device class to be used (default: infiniband)
      -p, --net-provider=                   Set the network fabric provider to be used
      -t, --use-tmpfs-scm                   Use tmpfs for scm rather than PMem
      -m, --control-metadata-path=          External storage path to store control metadata. Set this to
                                            a persistent location and specify --use-tmpfs-scm to create an
                                            MD-on-SSD config
      -f, --fabric-ports=                   Allow custom fabric interface ports to be specified for each engine
                                            config section. Comma separated port numbers, one per engine

The daos_server service must be running on the remote storage servers and as such a minimal server config file must already exist.

An example of a minimal config file is as follows which will enable basic validation to pass and the daos_server to start (see the Server startup section for help on starting the service):

$ cat /etc/daos/daos_server.yml
provider: ofi+tcp
engines:
- provider: ofi+tcp
  fabric_iface: ib0
  fabric_iface_port: 31416
  storage:
  - class: ram
    scm_mount: /mnt/daos0
    scm_size: 16

Config Generate Command Operation

The options that can be supplied to the config generate command are as follows:

• --access-points specifies the access points (identified storage servers that will host the management service for the DAOS system across the cluster).

• --num-engines specifies the number of engine sections to populate in the config file output. If not set explicitly on the commandline, default is the number of NUMA nodes detected on the host. Each generated engine section will specify a SCM storage tier (PMem or tmpfs) in addition to one or more NVMe storage tiers. All hardware components specified in an engine config section should be bound to the same NUMA node (PMem bdev, SSDs and host fabric interface).

• --scm-only requests that a config without NVMe should be generated. This flag will override the command's normal behavior and should be used only in circumstances where NVMe SSDs are unavailable or not balanced across NUMA nodes and multiple engines are required per host. Note that DAOS performance will be suboptimal without NVMe SSDs.

• --net-class selects a specific network device class, options are ethernet or infiniband. If not set explicitly on the commandline, default is infiniband. This option will alter the command's behavior and should only be used when normal command operation is not sufficient.

• --net-provider selects a specific network provider , this can be set to any provider string supported on the hosts e.g. ofi+tcp. This option will alter the command's behavior and should only be used when normal command operation is not sufficient. Note that specifying a provider will prevent the command from selecting the best available.

• --use-tmpfs-scm will produce a config specifying RAM-disk (tmpfs) devices in the first (SCM) storage tier. The RAM-disk sizes will be calculated based on the host's total memory (as reported by /proc/meminfo).

• --control-metadata-path specifies a persistent location to store control-plane metadata which allows MD-on-SSD DAOS deployments to survive without data loss over 'daos_server' restarts. If this option is set then a MD-on-SSD config will be generated.

• --fabric-ports enables custom port numbers to be assigned to each engine's fabric settings. Comma separated list must contain enough numbers to cover all engines generated in config.

The text generated by the command and output to stdout can be copied and used as the server config file on relevant hosts (normally by copying to /etc/daos/daos_server.yml and (re)starting service).

Config Generate Command Troubleshooting

The config generate command may fail to generate output in the following cases:

• When running with the dmg tool, if installed hardware device count or NUMA mappings differ on any of the hosts in the hostlist. The output of daos_server (scm|nvme|network) scan can be used to detect hardware differences between hosts, examples of differences that might prevent a config from being generated are NVMe SSD count, PCI address distribution or device NUMA affinities.

• NUMA node count can't be detected on the hosts or differs on any host in the host list.

• NUMA node count doesn't meet the num-engines requirement when --use-tmpfs-scm is specified.

• PMem device count or NUMA affinity doesn't meet the num-engines requirement.

• NVMe device NUMA affinity imbalanced (or all bound to one socket).

• Network device count or NUMA affinity doesn't match the num-engines requirement. Limitations regarding network device class and provider support should also be taken into account.

Config Generate Example Usage

The following example executes the daos_server config generate local command with commandline options to select a specific provider and use RAM-disk for SCM. The storage server has balanced NUMA Affinity for hardware components and therefore successfully generates a config with one fabric interface per socket/NUMA (one NUMA node per socket on the target host) and 8 NVMe SSDs per engine. The command redirects stderr to /dev/null and stdout to a temporary file. The installation is from a source build.

[user@wolf-226 daos]$ install/bin/daos_server config generate -p ofi+tcp --use-tmpfs-scm 2>/dev/null | tee ~/configs/tmp.yml
port: 10001
transport_config:
  allow_insecure: false
  client_cert_dir: /etc/daos/certs/clients
  ca_cert: /etc/daos/certs/daosCA.crt
  cert: /etc/daos/certs/server.crt
  key: /etc/daos/certs/server.key
engines:
- targets: 16
  nr_xs_helpers: 4
  first_core: 0
  log_file: /tmp/daos_engine.0.log
  storage:
  - class: ram
    scm_mount: /mnt/daos0
    scm_size: 85
  - class: nvme
    bdev_list:
    - 0000:2b:00.0
    - 0000:2c:00.0
    - 0000:2d:00.0
    - 0000:2e:00.0
    - 0000:63:00.0
    - 0000:64:00.0
    - 0000:65:00.0
    - 0000:66:00.0
  provider: ofi+tcp
  fabric_iface: ib0
  fabric_iface_port: 31416
  pinned_numa_node: 0
- targets: 16
  nr_xs_helpers: 4
  first_core: 0
  log_file: /tmp/daos_engine.1.log
  storage:
  - class: ram
    scm_mount: /mnt/daos1
    scm_size: 85
  - class: nvme
    bdev_list:
    - 0000:a2:00.0
    - 0000:a3:00.0
    - 0000:a4:00.0
    - 0000:a5:00.0
    - 0000:de:00.0
    - 0000:df:00.0
    - 0000:e0:00.0
    - 0000:e1:00.0
  provider: ofi+tcp
  fabric_iface: ib1
  fabric_iface_port: 32416
  pinned_numa_node: 1
disable_vfio: false
disable_vmd: false
enable_hotplug: false
nr_hugepages: 16384
disable_hugepages: false
control_log_mask: INFO
control_log_file: /tmp/daos_server.log
core_dump_filter: 19
name: daos_server
socket_dir: /var/run/daos_server
provider: ofi+tcp
access_points:
- localhost:10001
fault_cb: ""
hyperthreads: false

Now we start the daos_server service from the generated config which loads successfully and runs until the point where a storage format is required, as expected.

[user@wolf-226 daos]$ install/bin/daos_server start -i -o ~/configs/tmp.yml
DAOS Server config loaded from /home/user/configs/tmp.yml
install/bin/daos_server logging to file /tmp/daos_server.log
NOTICE: Configuration includes only one access point. This provides no redundancy in the event of an access point failure.
DAOS Control Server v2.3.101 (pid 1211553) listening on 127.0.0.1:10001
Checking DAOS I/O Engine instance 0 storage ...
Checking DAOS I/O Engine instance 1 storage ...
SCM format required on instance 0
SCM format required on instance 1

The daos_server start --auto-format option has now been added to allow automatic formatting on startup in the event that externally triggered format is not desirable. When using this option the storage format will occur on daos_server startup without any user intervention assuming the supplied config file is valid.

To manually format the storage and start the engine processes, we run the following on a separate terminal window and verify that engine processes (ranks) have registered with the system. Note the subsequent system query command may not show ranks started immediately after the storage format command returns so it is recommended to leave a short delay (~5s) before invoking.

[user@wolf-226 daos]$ install/bin/dmg storage format -i
Format Summary:
  Hosts     SCM Devices NVMe Devices
  -----     ----------- ------------
  localhost 2           16
[user@wolf-226 daos]$ install/bin/dmg system query -i
Rank  State
----  -----
[0-1] Joined

Engine I/O processes will be launched by the daos_server service following storage format.

Instance 0: starting format of nvme block devices 0000:2b:00.0,0000:2c:00.0,0000:2d:00.0,0000:2e:00.0,0000:63:00.0,0000:64:00.0,0000:65:00.0,0000:66:00.0
Instance 0: finished format of nvme block devices 0000:2b:00.0,0000:2c:00.0,0000:2d:00.0,0000:2e:00.0,0000:63:00.0,0000:64:00.0,0000:65:00.0,0000:66:00.0
Format of NVMe storage for DAOS I/O Engine instance 0: 6.15314273s
Writing NVMe config file for engine instance 0 to "/mnt/daos0/daos_nvme.conf"
Instance 1: starting format of nvme block devices 0000:a2:00.0,0000:a3:00.0,0000:a4:00.0,0000:a5:00.0,0000:de:00.0,0000:df:00.0,0000:e0:00.0,0000:e1:00.0
Instance 1: finished format of nvme block devices 0000:a2:00.0,0000:a3:00.0,0000:a4:00.0,0000:a5:00.0,0000:de:00.0,0000:df:00.0,0000:e0:00.0,0000:e1:00.0
Format of NVMe storage for DAOS I/O Engine instance 1: 6.15925073s
Writing NVMe config file for engine instance 1 to "/mnt/daos1/daos_nvme.conf"
DAOS I/O Engine instance 0 storage ready
DAOS I/O Engine instance 1 storage ready
SCM @ /mnt/daos1: 91 GB Total/91 GB Avail
Starting I/O Engine instance 1: /home/user/projects/daos/install/bin/daos_engine
daos_engine:1 Using NUMA core allocation algorithm
SCM @ /mnt/daos0: 91 GB Total/91 GB Avail
Starting I/O Engine instance 0: /home/user/projects/daos/install/bin/daos_engine
daos_engine:0 Using NUMA core allocation algorithm
MS leader running on wolf-226.wolf.hpdd.intel.com
daos_engine:1 DAOS I/O Engine (v2.3.101) process 1215202 started on rank 1 with 16 target, 4 helper XS, firstcore 0, host wolf-226.wolf.hpdd.intel.com.
Using NUMA node: 1
daos_engine:0 DAOS I/O Engine (v2.3.101) process 1215209 started on rank 0 with 16 target, 4 helper XS, firstcore 0, host wolf-226.wolf.hpdd.intel.com.
Using NUMA node: 0

For reference, the hardware scan results for the target storage server are included below.

[user@wolf-226 daos]$ install/bin/daos_server nvme scan
Scan locally-attached NVMe storage...
NVMe PCI     Model              FW Revision Socket ID Capacity
--------     -----              ----------- --------- --------
0000:2b:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:2c:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:2d:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:2e:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:63:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:64:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:65:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:66:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    0         3.8 TB
0000:a2:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:a3:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:a4:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:a5:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:de:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:df:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:e0:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB
0000:e1:00.0 MZXLR3T8HBLS-000H3 MPK7525Q    1         3.8 TB

[user@wolf-226 daos]$ install/bin/daos_server network scan
---------
localhost
---------

    -------------
    NUMA Socket 0
    -------------

        Provider          Interfaces
        --------          ----------
        ofi+tcp;ofi_rxm   eth0, ib0
        ucx+all           eth0, ib0, ib0
        ucx+dc            ib0
        ucx+rc_x          ib0
        ucx+tcp           eth0, ib0
        ofi+sockets       eth0, ib0
        ucx+dc_x          ib0
        ucx+rc_v          ib0
        ucx+ud            ib0
        ofi+verbs;ofi_rxm ib0
        ucx+rc            ib0
        ucx+ud_v          ib0
        ucx+ud_x          ib0
        udp;ofi_rxd       eth0, ib0
        udp               eth0, ib0
        ofi+tcp           eth0, ib0
        ofi+verbs         ib0

    -------------
    NUMA Socket 1
    -------------

        Provider          Interfaces
        --------          ----------
        ofi+tcp           ib1
        ofi+verbs;ofi_rxm ib1
        ucx+dc_x          ib1
        ucx+rc_x          ib1
        ucx+tcp           ib1
        ucx+ud            ib1
        ofi+sockets       ib1
        udp;ofi_rxd       ib1
        udp               ib1
        ucx+dc            ib1
        ucx+all           ib1, ib1
        ofi+verbs         ib1
        ucx+rc            ib1
        ucx+rc_v          ib1
        ucx+ud_v          ib1
        ucx+ud_x          ib1
        ofi+tcp;ofi_rxm   ib1

Certificate Configuration

The DAOS security framework relies on certificates to authenticate components and administrators in addition to encrypting DAOS control plane communications. A set of certificates for a given DAOS system may be generated by running the gen_certificates.sh script provided with the DAOS software if there is not an existing TLS certificate infrastructure. The gen_certificates.sh script uses the openssl tool to generate all of the necessary files. We highly recommend using OpenSSL Version 1.1.1h or higher as keys and certificates generated with earlier versions are vulnerable to attack.

When DAOS is installed from RPMs, this script is provided in the base daos RPM, and may be invoked in the directory to which the certificates will be written. As part of the generation process, a new local Certificate Authority is created to handle certificate signing, and three role certificates are created:

# /usr/lib64/daos/certgen/gen_certificates.sh
Generating Private CA Root Certificate
Private CA Root Certificate created in ./daosCA
...
Generating Server Certificate
Required Server Certificate Files:
        ./daosCA/certs/daosCA.crt
        ./daosCA/certs/server.key
        ./daosCA/certs/server.crt
...
Generating Agent Certificate
Required Agent Certificate Files:
        ./daosCA/certs/daosCA.crt
        ./daosCA/certs/agent.key
        ./daosCA/certs/agent.crt
...
Generating Admin Certificate
Required Admin Certificate Files:
        ./daosCA/certs/daosCA.crt
        ./daosCA/certs/admin.key
        ./daosCA/certs/admin.crt

The files generated under ./daosCA should be protected from unauthorized access and preserved for future use.

The generated keys and certificates must then be securely distributed to all nodes participating in the DAOS system (servers, clients, and admin nodes). Permissions for these files should be set to prevent unauthorized access to the keys and certificates.

Client nodes require:

• CA root cert
• Agent cert
• Agent key

Administrative nodes require:

• CA root cert
• Admin cert
• Admin key

Server nodes require:

• CA root cert
• Server cert
• Server key
• All valid agent certs in the DAOS system (in the client cert directory, see config file below)

After the certificates have been securely distributed, the DAOS configuration files must be updated in order to enable authentication and secure communications. These examples assume that the configuration and certificate files have been installed under /etc/daos:

# /etc/daos/daos_server.yml (servers)

transport_config:
  # Location where daos_server will look for Client certificates
  client_cert_dir: /etc/daos/certs/clients
  # Custom CA Root certificate for generated certs
  ca_cert: /etc/daos/certs/daosCA.crt
  # Server certificate for use in TLS handshakes
  cert: /etc/daos/certs/server.crt
  # Key portion of Server Certificate
  key: /etc/daos/certs/server.key

# /etc/daos/daos_agent.yml (clients)

transport_config:
  # Custom CA Root certificate for generated certs
  ca_cert: /etc/daos/certs/daosCA.crt
  # Agent certificate for use in TLS handshakes
  cert: /etc/daos/certs/agent.crt
  # Key portion of Agent Certificate
  key: /etc/daos/certs/agent.key

# /etc/daos/daos_control.yml (dmg/admin)

transport_config:
  # Custom CA Root certificate for generated certs
  ca_cert: /etc/daos/certs/daosCA.crt
  # Admin certificate for use in TLS handshakes
  cert: /etc/daos/certs/admin.crt
  # Key portion of Admin Certificate
  key: /etc/daos/certs/admin.key

Server Startup

The DAOS Server is started as a systemd service. The DAOS Server unit file is installed in the correct location when installing from RPMs. The DAOS Server will be run as daos-server user which will be created during RPM install.

If you wish to use systemd with a development build, you must copy the service file from utils/systemd to /usr/lib/systemd/system. Once the file is copied, modify the ExecStart line to point to your daos_server binary.

After modifying ExecStart, run the following command:

$ sudo systemctl daemon-reload

Once the service file is installed you can start daos_server with the following commands:

$ systemctl enable daos_server.service
$ systemctl start daos_server.service

To check the component status use:

$ systemctl status daos_server.service

If DAOS Server failed to start, check the logs with:

$ journalctl --unit daos_server.service

After RPM install, daos_server service starts automatically running as user "daos". The server config is read from /etc/daos/daos_server.yml and certificates are read from /etc/daos/certs. With no other admin intervention other than the loading of certificates, daos_server will enter a listening state enabling discovery of storage and network hardware through the dmg tool without any I/O engines specified in the configuration file. After device discovery and provisioning, an updated configuration file with a populated per-engine section can be stored in /etc/daos/daos_server.yml, and after reestarting the daos_server service it is then ready for the storage to be formatted.

DAOS Server Remote Access

Remote tasking of the DAOS system and individual DAOS Server processes can be performed via the dmg utility.

To set the addresses of which DAOS Servers to task, provide either:

• -l <hostlist> on the commandline when invoking, or

• hostlist: <hostlist> in the control configuration file daos_control.yml

Where <hostlist> represents a slurm-style hostlist string e.g. foo-1[28-63],bar[256-511]. The first entry in the hostlist (after alphabetic then numeric sorting) will be assumed to be the access point as set in the server configuration file.

Local configuration files stored in the user directory will be used in preference to the default location e.g. ~/.daos_control.yml.

Hardware Provisioning

Once the DAOS server started, the storage and network can be configured on the storage nodes via the dmg utility.

Note

daos_server (nvme|scm) commands are config aware meaning they will read parameters from the server configuration file unless the --ignore-config flag is supplied.

SCM Preparation

This section addresses how to verify that PMem (Intel(R) Optane(TM) persistent memory) modules are correctly installed on the storage nodes and how to configure them in interleaved mode to be used by DAOS. Instructions for other types of SCM may be covered in the future.

Provisioning the SCM occurs by configuring PMem modules in interleaved memory regions (interleaved mode) in groups of modules local to a specific socket (NUMA), and resultant PMem namespaces are defined by a device identifier (e.g., /dev/pmem0).

PMem preparation is required once per DAOS installation.

This step requires a reboot to enable PMem resource allocation changes to be read by BIOS.

PMem preparation can be performed with daos_server scm prepare.

The first time the command is run, the SCM interleaved regions will be created as resource allocations on any available PMem modules (one region per socket). The regions are activated after BIOS reads the new resource allocations. Upon completion, the scm prepare command will prompt the admin to reboot the storage node(s) in order for the BIOS to activate the new storage allocations. The scm prepare command does not initiate the reboot itself.

After running the command a reboot will be required, the command will then need to be run for a second time to expose the namespace device to be used by DAOS.

Example usage:

• clush -w wolf-[118-121,130-133] daos_server scm prepare after running, the user should be prompted for a reboot.

• clush -w wolf-[118-121,130-133] reboot

• clush -w wolf-[118-121,130-133] daos_server scm prepare after running, PMem namespaces (/dev/pmemX block devices created on the new SCM regions) should be available on each of the hosts.

On the second run, one namespace per region is created, and each namespace may take up to a few minutes to create. Details of the PMem namespaces will be displayed in JSON format on command completion.

Upon successful creation of the PMem namespaces, the Intel(R) Optane(TM) persistent memory is configured and one can move on to the next step.

If required, the PMem namespaces can be destroyed with the command daos_server scm reset.

All namespaces are disabled and destroyed. The SCM regions are removed by resetting modules into "MemoryMode" through resource allocations.

Warning

Undefined behavior may result if the namespaces/pmem kernel block devices are mounted when running the reset command (as per the printed warning).

A subsequent reboot is required for BIOS to read the new resource allocations.

Multiple PMem namespaces per socket (Experimental)

By default the daos_server scm prepare command will create one PMem namespace on each PMem region. A single PMem AppDirect region will be created for each NUMA node (typically one NUMA node per CPU socket) in interleaved mode (which indicates that all PMem modules attached to a particular socket will be used in a single set/region). Therefore by default on a dual-socket platform, two regions and two namespaces will be created.

Multiple PMem namespaces can be created on a single region (one per socket) by specifying a value of 1-8 in (-S|--scm-ns-per-socket) commandline option for daos_server scm prepare subcommand.

Example usage:

$ daos_server scm prepare -f -S 4
Prepare locally-attached SCM...
Memory allocation goals for PMem will be changed and namespaces modified, this may be a destructive
operation. Please ensure namespaces are unmounted and locally attached PMem modules are not in use.
Please be patient as it may take several minutes and subsequent reboot maybe required.
SCM Namespace Socket ID Capacity
------------- --------- --------
pmem0         0         796 GB
pmem0.1       0         796 GB
pmem0.2       0         796 GB
pmem0.3       0         796 GB
pmem1         1         796 GB
pmem1.1       1         796 GB
pmem1.2       1         796 GB
pmem1.3       1         796 GB

Note

This feature is in a beta phase and not supported in production deployments.

Storage Discovery and Selection

This section covers how to manually detect and select storage devices to be used by DAOS. The server configuration file gives an administrator the ability to control storage selection.

Note

daos_server (nvme|scm) commands are config aware meaning they will read parameters from the server configuration file unless the --ignore-config flag is supplied.

Discovery

DAOS tools will discover NVMe SSDs and Persistent Memory Modules using the storage scan commands.

dmg storage scan can be run to query remote running daos_server processes over the management network.

daos_server (nvme|scm) scan can be used to query storage on the local host directly.

Note

'daos_server' commands will refuse to run if a process with the same name exists (e.g. as a systemd service under the 'daos_server' userid).

NVMe SSDs no longer need to be made accessible first by running daos_server nvme prepare, daos_server nvme scan will take the necessary steps to prepare the devices unless --skip-prep flag is supplied.

The default way for DAOS to access NVMe storage is through SPDK via the VFIO user-space driver. To use an alternative driver with SPDK, set --disable-vfio in the nvme prepare command to fallback to using UIO user-space driver with SPDK instead.

Note

If UIO user-space driver is used instead of VFIO, 'daos_server' needs to be run as root.

The output will be equivalent running dmg storage scan --verbose remotely.

bash-4.2$ dmg storage scan
Hosts        SCM Total             NVMe Total
-----        ---------             ----------
wolf-[71-72] 6.4 TB (2 namespaces) 3.1 TB (3 controllers)

bash-4.2$ dmg storage scan --verbose
------------
wolf-[71-72]
------------
SCM Namespace Socket ID Capacity
------------- --------- --------
pmem0         0         3.2 TB
pmem1         1         3.2 TB

NVMe PCI     Model                FW Revision Socket ID Capacity
--------     -----                ----------- --------- --------
0000:81:00.0 INTEL SSDPED1K750GA  E2010325    1         750 GB
0000:87:00.0 INTEL SSDPEDMD016T4  8DV10171    1         1.6 TB
0000:da:00.0 INTEL SSDPED1K750GA  E2010325    1         750 GB

The NVMe PCI field above is what should be used in the server configuration file to identified NVMe SSDs.

Devices with the same NUMA node/socket should be used in the same per-engine section of the server configuration file for best performance.

For further info on dmg storage command usage run dmg storage --help.

To release the NVMe drives from the user-space drivers and bind them back to the kernel "nvme" driver so they can be used by the OS (and reappear as /dev/nvme* block devices), run daos_server nvme reset with any relevant options (see command help for details). The reset command will also release any hugepages used by no-longer-active SPDK processes.

daos_server nvme scan will perform a subsequent reset implicitly so manual reset is not required but a stopped daos_server may not reset device bindings and hugepage resources and may require a manual reset to do so.

Warning

Due to SPDK issue 2926, if VMD is enabled and PCI_ALLOWED list is set to a subset of available VMD controllers (as specified in the server config file) then the backing devices of the unselected VMD controllers will be bound to no driver and therefore inaccessible from both OS and SPDK. Workaround is to run daos_server nvme scan --ignore-config to reset driver bindings for all VMD controllers.

Health

SSD health state can be verified via dmg storage scan --nvme-health:

bash-4.2$ dmg storage scan --nvme-health
-------
wolf-71
-------
PCI:0000:81:00.0 Model:INTEL SSDPED1K750GA  FW:E2010325 Socket:1 Capacity:750 GB
  Health Stats:
    Timestamp:2021-09-13T11:12:34.000+00:00
    Temperature:318K(44.85C)
    Controller Busy Time:0s
    Power Cycles:15
    Power On Duration:10402h0m0s
    Unsafe Shutdowns:13
    Error Count:0
    Media Errors:0
    Read Errors:0
    Write Errors:0
    Unmap Errors:0
    Checksum Errors:0
    Error Log Entries:0
  Critical Warnings:
    Temperature: OK
    Available Spare: OK
    Device Reliability: OK
    Read Only: OK
    Volatile Memory Backup: OK
  Intel Vendor SMART Attributes:
    Program Fail Count:
       Normalized:100%
       Raw:0
    Erase Fail Count:
       Normalized:100%
       Raw:0
    Wear Leveling Count:
       Normalized:100%
       Min:0
       Max:9
       Avg:3
    End-to-End Error Detection Count:0
    CRC Error Count:0
    Timed Workload, Media Wear:65535
    Timed Workload, Host Read/Write Ratio:65535
    Timed Workload, Timer:65535
    Thermal Throttle Status:0%
    Thermal Throttle Event Count:0
    Retry Buffer Overflow Counter:0
    PLL Lock Loss Count:0
    NAND Bytes Written:222897
    Host Bytes Written:71

PCI:0000:da:00.0 Model:INTEL SSDPED1K750GA  FW:E2010325 Socket:1 Capacity:750 GB
  Health Stats:
    Temperature:320K(46.85C)
    Controller Busy Time:0s
    Power Cycles:15
    Power On Duration:10402h0m0s
    Unsafe Shutdowns:13
    Error Count:0
    Media Errors:0
    Read Errors:0
    Write Errors:0
    Unmap Errors:0
    Checksum Errors:0
    Error Log Entries:0
  Critical Warnings:
    Temperature: OK
    Available Spare: OK
    Device Reliability: OK
    Read Only: OK
    Volatile Memory Backup: OK
  Intel Vendor SMART Attributes:
    Program Fail Count:
       Normalized:100%
       Raw:0
    Erase Fail Count:
       Normalized:100%
       Raw:0
    Wear Leveling Count:
       Normalized:100%
       Min:0
       Max:9
       Avg:3
    End-to-End Error Detection Count:0
    CRC Error Count:0
    Timed Workload, Media Wear:65535
    Timed Workload, Host Read/Write Ratio:65535
    Timed Workload, Timer:65535
    Thermal Throttle Status:0%
    Thermal Throttle Event Count:0
    Retry Buffer Overflow Counter:0
    PLL Lock Loss Count:0
    NAND Bytes Written:222897
    Host Bytes Written:71

-------
wolf-72
-------
PCI:0000:81:00.0 Model:INTEL SSDPED1K750GA  FW:E2010435 Socket:1 Capacity:750 GB
  Health Stats:
    Temperature:316K(42.85C)
    Controller Busy Time:8m0s
    Power Cycles:23
    Power On Duration:10399h0m0s
    Unsafe Shutdowns:18
    Error Count:0
    Media Errors:0
    Read Errors:0
    Write Errors:0
    Unmap Errors:0
    Checksum Errors:0
    Error Log Entries:0
  Critical Warnings:
    Temperature: OK
    Available Spare: OK
    Device Reliability: OK
    Read Only: OK
    Volatile Memory Backup: OK
  Intel Vendor SMART Attributes:
    Program Fail Count:
       Normalized:100%
       Raw:0
    Erase Fail Count:
       Normalized:100%
       Raw:0
    Wear Leveling Count:
       Normalized:100%
       Min:0
       Max:9
       Avg:3
    End-to-End Error Detection Count:0
    CRC Error Count:0
    Timed Workload, Media Wear:65535
    Timed Workload, Host Read/Write Ratio:65535
    Timed Workload, Timer:65535
    Thermal Throttle Status:0%
    Thermal Throttle Event Count:0
    Retry Buffer Overflow Counter:0
    PLL Lock Loss Count:0
    NAND Bytes Written:222897
    Host Bytes Written:71

PCI:0000:da:00.0 Model:INTEL SSDPED1K750GA  FW:E2010435 Socket:1 Capacity:750 GB
  Health Stats:
    Temperature:320K(46.85C)
    Controller Busy Time:1m0s
    Power Cycles:23
    Power On Duration:10399h0m0s
    Unsafe Shutdowns:19
    Error Count:0
    Media Errors:0
    Read Errors:0
    Write Errors:0
    Unmap Errors:0
    Checksum Errors:0
    Error Log Entries:0
  Critical Warnings:
    Temperature: OK
    Available Spare: OK
    Device Reliability: OK
    Read Only: OK
    Volatile Memory Backup: OK
  Intel Vendor SMART Attributes:
    Program Fail Count:
       Normalized:100%
       Raw:0
    Erase Fail Count:
       Normalized:100%
       Raw:0
    Wear Leveling Count:
       Normalized:100%
       Min:0
       Max:9
       Avg:3
    End-to-End Error Detection Count:0
    CRC Error Count:0
    Timed Workload, Media Wear:65535
    Timed Workload, Host Read/Write Ratio:65535
    Timed Workload, Timer:65535
    Thermal Throttle Status:0%
    Thermal Throttle Event Count:0
    Retry Buffer Overflow Counter:0
    PLL Lock Loss Count:0
    NAND Bytes Written:222897
    Host Bytes Written:71

Selection

The next step consists of specifying the devices that should be used by DAOS in the server configuration YAML file. The engines section of the config is a list with details for each DAOS engine to be started on the host (one engine will be created for each entry in list).

Devices with the same NUMA rating/node/socket should be colocated on a single DAOS engine where possible. See the server configuration file section for more details.

Storage is specified for each engine in a storage list with each entry in the list defining an individual storage tier.

Each tier has a class parameter which defines the storage type. Typical class values are "dcpm" for PMem (Intel(R) Optane(TM) persistent memory) and "nvme" for NVMe SSDs. When persistent memory is unavailable, class may be set to "ram", which emulates SCM using a ramfs device, and metadata and small objects are saved to NVMe SSDs using logging and checkpointing.

For class == "dcpm", the following parameters should be populated:

• scm_list should should contain PMem interleaved-set namespaces (e.g. /dev/pmem1). Currently the size of the list is limited to 1.
• scm_mount gives the desired local directory to be used as the mount point for DAOS persistent storage mounted on the specified PMem device specified in scm_list.

For class == "ram", scm_list is omitted and scm_size is specified instead. In this case, the subsequent bdev tiers describe the persistent storage used for both data and metadata.

• scm_size specifies the amount of RAM dedicated to emulate SCM for holding DAOS metadata. As with SCM, the RAM size must be sufficient to hold metadata to accommodate the size of data tiers. Required metadata to data ratios vary by usage, but typically metadata size will only be a few percent of data. The storage requirements discussion of the ratio between SCM size and the size of NVMe data tiers is relevant, as the required RAM / NVMe ratio will be similar.

For class == "nvme", the following parameters should be populated:

• bdev_list should be populated with NVMe PCI addresses.
• bdev_roles optionally specifies a list of roles for this tier. By default, the DAOS server will assign roles to bdev tiers automatically, so the bdev_roles directive is only needed when that assignment doesn't match your use case.

When "dcpm" is used for the first tier, this list should be omitted or specify only "data". Only a single NVMe tier is supported.

When class == "ram" is used, the NVMe tier roles can be one or more of "wal" (write-ahead-log for tracking the changes made by local transactions), "meta" (for persistent metadata and small object storage), or "data" (contents of larger objects). Only the "data" role may be assigned to multiple tiers. If no roles are specified, then the server will assign them. Otherwise all roles must be assigned to a tier.

See the sample configuration file daos_server.yml and example configuration files in the examples directory for more details.

The default way for DAOS to access NVMe storage is through SPDK via the VFIO user-space driver. To use an alternative driver with SPDK, set disable_vfio: true in the global section of the server config file to fallback to using UIO user-space driver with SPDK instead.

Note

If UIO user-space driver is used instead of VFIO, 'daos_server' needs to be run as root.

If VMD is enabled on a host, its usage will be enabled by default meaning that the bdev_list device addresses will be interpreted as VMD endpoints and storage scan will report the details of the physical NVMe backing devices that belong to each VMD endpoint. To disable the use of VMD on a VMD-enabled host, set disable_vmd: true in the global section of the config to fallback to using physical NVMe devices only.

Warning

If upgrading from DAOS 2.0 to a greater version, the old 'enable_vmd' server config file parameter is no longer honored and instead should be removed (or replaced by disable_vmd: true if VMD is to be explicitly disabled).

Otherwise 'daos_server' may fail config validation and not start after an update from 2.0 to a greater version.

Example Configurations

To illustrate, assume a cluster with homogeneous hardware configurations that returns the following from scan for each host:

[daos@wolf-72 daos_m]$ dmg -l wolf-7[1-2] storage scan --verbose
-------
wolf-7[1-2]
-------
SCM Namespace Socket ID Capacity
------------- --------- --------
pmem0         0         2.90TB
pmem1         1         2.90TB

NVMe PCI     Model                FW Revision Socket ID Capacity
--------     -----                ----------- --------- --------
0000:81:00.0 INTEL SSDPED1K750GA  E2010325    0         750.00GB
0000:87:00.0 INTEL SSDPEDMD016T4  8DV10171    0         1.56TB
0000:da:00.0 INTEL SSDPED1K750GA  E2010325    1         750.00GB

In this situation, the configuration file engines section could be populated as follows to establish 2-tier storage:

<snip>
port: 10001
access_points: ["wolf-71"] # <----- updated
<snip>
engines:
-
  pinned_numa_node: 0         # run 1st engine on CPU 0
  targets: 16                 # number of I/O service threads per-engine
  nr_xs_helpers: 4            # count of I/O offload threads
  fabric_iface: eth0          # network interface to use for this engine
  fabric_iface_port: 31416    # network port
  log_mask: ERR               # debug level to start with the engine with
  log_file: /tmp/server1.log  # where to store engine logs
  storage:
  -
    class: dcpm               # type of first storage tier (SCM)
    scm_list: [/dev/pmem0]    # <----- updated
    scm_mount: /mnt/daos0     # where to mount SCM
  -
    class: nvme               # type of second storage tier (NVMe)
    bdev_list: ["0000:87:00.0"] # <----- updated
-
  pinned_numa_node: 1
  targets: 16
  nr_xs_helpers: 4
  fabric_iface: eth0
  fabric_iface_port: 32416
  log_mask: ERR
  log_file: /tmp/server2.log
  storage:
  -
    class: dcpm               # type of first storage tier (SCM)
    scm_list: [/dev/pmem1]    # <----- updated
    scm_mount: /mnt/daos1     # where to mount SCM
  -
    class: nvme               # type of second storage tier (NVMe)
    bdev_list: ["0000:da:00.0"] # <----- updated
<end>

There are a few optional providers that are not built by default. For detailed information, please refer to the DAOS build documentation.

Note

DAOS Control Servers will need to be restarted on all hosts after updates to the server configuration file.

Pick an odd number of hosts in the system and set access_points to list of that host's hostname or IP address (don't need to specify port).

This will be the host which bootstraps the DAOS management service (MS).

The support of the optional providers is not guarantee and can be removed without further notification.

Network Configuration

Network Scan

The dmg utility supports the network scan function to display the network interfaces, related OFI fabric providers and associated NUMA node for each device. This information is used to configure the global fabric provider and the unique local network interface for each I/O engine on the storage nodes. This section will help you determine what to provide for the provider, fabric_iface and pinned_numa_node entries in the daos_server.yml file.

The following commands are typical examples:

$ dmg network scan
$ dmg network scan -p all
$ dmg network scan -p ofi+tcp
$ dmg network scan --provider ofi+verbs

In the early stages when a daos_server has not yet been fully configured and lacks a declaration of the system's fabric provider, it may be helpful to view an unfiltered list of scan results.

Use either of these dmg commands in the early stages to accomplish this goal:

$ dmg network scan
$ dmg network scan -p all

Typical network scan results look as follows:

$ dmg network scan
-------
wolf-29
-------

    -------------
    NUMA Socket 1
    -------------

        Provider    Interfaces
        --------    ----------
        ofi+tcp     ib1

---------
localhost
---------

    -------------
    NUMA Socket 0
    -------------

        Provider    Interfaces
        --------    ----------
        ofi+tcp     ib0, eth0

    -------------
    NUMA Socket 1
    -------------

        Provider    Interfaces
        --------    ----------
        ofi+tcp     ib1

Use one of these providers to configure the provider in the daos_server.yml. Only one provider may be specified for the entire DAOS installation. Client nodes must be capable of communicating to the daos_server nodes via the same provider. Therefore, it is helpful to choose network settings for the daos_server that are compatible with the expected client node configuration.

After the daos_server.yml file has been edited and contains a provider, subsequent dmg network scan commands will filter the results based on that provider. If it is desired to view an unfiltered list again, issue dmg network scan -p all.

Regardless of the provider in the daos_server.yml file, the results may be filtered to the specified provider with the command dmg network scan -p ofi_provider where ofi_provider is one of the available providers from the list.

The results of the network scan may be used to help configure the I/O engines.

Each I/O engine is configured with a unique fabric_iface and optional pinned_numa_node. The interfaces and NUMA Sockets listed in the scan results map to the daos_server.yml fabric_iface and pinned_numa_node respectively. The use of pinned_numa_node is optional, but recommended for best performance. When specified with the value that matches the network interface, the I/O engine will bind itself to that NUMA node and to cores purely within that NUMA node. This configuration yields the fastest access to that network device.

Changing Network Providers

Information about the network configuration is stored as metadata on the DAOS storage.

If, after initial deployment, the provider must be changed, it is necessary to reformat the storage devices using dmg storage format after the configuration file has been updated with the new provider.

Provider Testing

Then, the fi_pingpong test can be used to verify that the targeted OFI provider works fine:

node1$ fi_pingpong -p verbs

node2$ fi_pingpong -p verbs ${IP_ADDRESS_NODE1}

bytes #sent #ack total time  MB/sec  usec/xfer Mxfers/sec
64    10    =10  1.2k  0.00s 21.69   2.95      0.34
256   10    =10  5k    0.00s 116.36  2.20      0.45
1k    10    =10  20k   0.00s 379.26  2.70      0.37
4k    10    =10  80k   0.00s 1077.89 3.80      0.26
64k   10    =10  1.2m  0.00s 2145.20 30.55     0.03
1m    10    =10  20m   0.00s 8867.45 118.25    0.01

CPU Resources

The I/O engine is multi-threaded, and the number of I/O service threads and helper threads that should be used per engine must be configured in the engines: section of the daos_server.yml file.

The number of I/O service threads is configured with the targets: setting. Each storage target manages a fraction of the (interleaved) SCM storage space, and a fraction of one of the NVMe SSDs that are managed by this engine. The optimal number of storage targets per engine depends on two conditions:

• For optimal balance regarding the NVMe space, the number of targets should be an integer multiple of the number of NVMe disks that are configured in the bdev_list: of the engine.

• To obtain the maximum SCM performance, a certain number of targets is needed. This is device- and workload-dependent, but around 16 targets usually work well.

It is recommended to also specify a number of I/O offloading threads with the nr_xs_helpers: setting. These threads can improve performance by offloading activities like checksum calculation and the dispatching of server-side RPCs from the main I/O service threads. When using EC, it is recommended to configure roughly one offloading thread per four target threads, for example targets: 16 and nr_xs_helpers: 4.

The server should have sufficiently many physical cores to support the number of targets plus the additional service threads.

Storage Formatting

Once the daos_server has been restarted with the correct storage devices, network interface, and CPU threads to use, one can move to the format phase. When daos_server is started for the first time, it enters "maintenance mode" and waits for a dmg storage format call to be issued from the management tool. This remote call will trigger the formatting of the locally attached storage on the host for use with DAOS using the parameters defined in the server config file.

dmg -l <host>[,...] storage format will normally be run on a login node specifying a hostlist (-l <host>[,...]) of storage nodes with SCM/PMem modules and NVMe SSDs installed and prepared.

Upon successful format, DAOS Control Servers will start DAOS I/O engines that have been specified in the server config file.

Successful start-up is indicated by the following on stdout: DAOS I/O Engine (v2.0.1) process 433456 started on rank 1 with 8 target, 2 helper XS, firstcore 0, host wolf-72.wolf.hpdd.intel.com.

SCM Format

When the command is run, the pmem kernel devices created on SCM/PMem regions are formatted and mounted based on the parameters provided in the server config file.

• scm_mount specifies the location of the mountpoint to create.
• scm_class can be set to ram to use a tmpfs in the situation that no SCM/PMem is available (scm_size dictates the size of tmpfs in GB), when set to dcpm the device specified under scm_list will be mounted at scm_mount path.

NVMe Format

When the command is run, NVMe SSDs are formatted and set up to be used by DAOS based on the parameters provided in the server config file.

bdev_class can be set to nvme to use actual NVMe devices with SPDK for DAOS storage. Other bdev_class values can be used for emulation of NVMe storage as specified in the server config file. bdev_list identifies devices to use with a list of PCI addresses (this can be populated after viewing results from storage scan command).

After the format command is run, the path specified by the server configuration file scm_mount parameter should be mounted and should contain a file named daos_nvme.conf. The file should describe the devices with PCI addresses as listed in the bdev_list parameter of the server config file. The presence and contents of the file indicate that the specified NVMe SSDs have been configured correctly for use with DAOS.

The contents of the NVMe SSDs listed in the server configuration file bdev_list parameter will be reset on format.

Server Format

Before the format command is run, no DAOS metadata should exist under the path specified by scm_mount parameter in the server configuration file.

After the storage format command is run, the path specified by the server configuration file scm_mount parameter should be mounted and should contain the necessary DAOS metadata indicating that the server has been formatted.

When starting, daos_server will skip maintenance mode and attempt to start I/O engines if valid DAOS metadata is found in scm_mount.

Agent Setup

This section addresses how to configure the DAOS Agents on the client nodes.

Agent User and Group Setup

The daos_agent daemon runs as an unprivileged user process, with the username daos_agent and group name daos_agent. If those IDs do not exist at the time the daos-client RPM is installed, they will be created during the RPM installation. Refer to User and Group Management for details.

Agent Certificate Generation

The DAOS security framework relies on SSL certificates to authenticate the DAOS daemon processes, as well as the DAOS administrators who run the dmg command. Refer to Certificate Generation for details on creating the necessary certificates.

Note

It is possible to disable the use of certificates for testing purposes.

This should never be done in production environments.

Running in insecure mode will allow arbitrary un-authenticated user processes to access and potentially damage the DAOS storage.

Agent Configuration File

The daos_agent configuration file is parsed when starting the daos_agent process. The configuration file location can be specified on the command line with the -o option (see daos_agent -h for usage help). Otherwise, the default location /etc/daos/daos_agent.yml will be used. When running daos_agent under systemd control, the default location is used unless the ExecStart line in the daos_agent.service file is modified to include the -o option.

Parameter descriptions are specified in the sample daos_agent.yml file, which will also get installed into /etc/daos/daos_agent.yml during the installation of the daos-client RPM.

Any option supplied to daos_agent as a command line option or flag will take precedence over equivalent configuration file parameter.

The following section lists the format, options, defaults, and descriptions available in the configuration file.

Defining fabric interfaces manually

By default, the DAOS Agent automatically detects all fabric interfaces on the client node. It selects an appropriate one for DAOS I/O based on the NUMA node of the client request and the interface type preferences reported by the DAOS management service.

If the DAOS Agent does not detect the fabric interfaces correctly, the administrator may define them manually in the Agent configuration file. These fabric_iface entries must be organized by NUMA node. If using the verbs provider, the interface domain is also required.

Example:

fabric_ifaces:
-
  numa_node: 0
  devices:
  -
    iface: ib0
    domain: mlx5_0
  -
    iface: ib1
    domain: mlx5_1
-
  numa_node: 1
  devices:
  -
    iface: ib2
    domain: mlx5_2
  -
    iface: ib3
    domain: mlx5_3

Agent Startup

The DAOS Agent is a standalone application to be run on each client node. By default, the DAOS Agent will be run as a systemd service. The DAOS Agent unit file is installed in the correct location (/usr/lib/systemd/system/daos_agent.service) during RPM installation.

After the RPM installation, and after the Agent configuration file has been created, the following commands will enable the DAOS Agent to be started at the next reboot, will start it immediately, and will check the status of the Agent after being started:

$ sudo systemctl enable daos_agent.service
$ sudo systemctl start  daos_agent.service
$ sudo systemctl status daos_agent.service

If the DAOS Agent fails to start, check the systemd logs for errors:

$ sudo journalctl --unit daos_agent.service

Starting the DAOS Agent with a non-default configuration

To start the DAOS Agent from the command line, for example to run with a non-default configuration file, run:

$ daos_agent -o <'path to agent configuration file/daos_agent.yml'> &

If you wish to use systemd with a development build, you must copy the Agent service file from utils/systemd/ to /usr/lib/systemd/system/. Then modify the ExecStart line to point to your Agent configuration file:

ExecStart=/usr/bin/daos_agent -o <'path to agent configuration file/daos_agent.yml'>

Once the service file is installed and systemctl daemon-reload has been run to reload the configuration, the daos_agent can be started through systemd as shown above.

Disable Agent Cache (Optional)

In certain circumstances (e.g. for DAOS development or system evaluation), it may be desirable to disable the DAOS Agent's caching mechanism in order to avoid stale system information being retained across reformats of a system. The DAOS Agent normally caches a map of rank-to-fabric URI lookups as well as client network configuration data in order to reduce the number of management RPCs required to start an application. When this information becomes stale, the Agent must be restarted in order to repopulate the cache with new information. Alternatively, the caching mechanism may be disabled, with the tradeoff that each application launch will invoke management RPCs in order to obtain system connection information.

To disable the DAOS Agent caching mechanism, set the following environment variable before starting the daos_agent process:

DAOS_AGENT_DISABLE_CACHE=true

If running from systemd, add the following to the daos_agent service file in the [Service] section before reloading systemd and restarting the daos_agent service:

Environment=DAOS_AGENT_DISABLE_CACHE=true

Multi-user DFuse setup

Running a single-user dfuse instance, for example on a compute node, requires no special setup. However configuration is required for allowing multi-user dfuse on a node.

Updating fuse config

Multi-user dfuse makes use of the allow_other fuse mount option which allows requests from users other than the user running dfuse. For reasons of safety this option is disabled by default for fuse and must be enabled by root before any user can use it. To allow this then root must add or uncomment a line in /etc/fuse.conf to enable the user_allow_other setting. The daos-client rpm does not do this automatically. An administrator must set this option on all nodes on which they want to provide a persistent multi-user dfuse service.

---

1. https://github.com/intel/ipmctl ↩

2. https://github.com/daos-stack/daos/tree/release/2.4/utils/config ↩

3. https://www.open-mpi.org/faq/?category=running#mpirun-hostfile ↩

4. https://github.com/daos-stack/daos/tree/release/2.4/src/control/README.md ↩

5. https://github.com/pmem/ndctl/issues/130 ↩